......................................................................

Italian - ItalyEnglish (United Kingdom)Español(Spanish Formal International)

......................................................................

AIRON s.r.l.
Via Marcinelle n° 8
45100 BORSEA (RO) - ITALY
Phone: +39 0425 471575
Fax: +39 0425 404037
info@airon-pneumatic.com

C.F. - P.IVA - N. REG. IMP. IT 01099010298
N. ISCR. R.E.A. 127012

Cylinders with position transducer

Extract from catalogue - cylinders with position transducer (1Mb)

Drawings DXF
Drawings DWG

3D drawings in STP format - documents freely available with registration

POT
Cylinder with position transducer

Cylinders with position transducer series POT series are actuators with ISO 15552 standard overall dimension equipped with a perfectly integrated potentiometric linear tranducer inside. That device allows to detect the piston position with good accuracy along the whole stroke matching the electric signal with the position. Standard version has a voltage signal but on request cylinder can be equipped with useful converters to get out a stabilized signal (voltage or current)

Instructions for good operating system
1) Linear potentiometer inside has to be used like a voltage divider not like a rheostat therefore it is suggested to connect it to an high impedence device (like a programmable logic controller).
2) Due to the working principle of the transducer (magnetic coupling movement) it has a high grade of electrical insulation from the medium. However, permissible acceleration has not to be over 10 m/s2 to avoid any decoupling between the piston and the transducer.
3) Standard strokes (see the order code page) allow an optimal use of the potentiometric device; however, in case of lesser stroke then the nominal one, keep in mind that it's not possible to use the whole range of signal. Example: if the stroke is 125 mm (standard stroke transducer is 150) and the applied voltage is 10 volts it can be operated only 5/6 of it (8,3 Volts).

 

Order codes
POT F M . 0 4 0 . 0 2 5 0 . S S . 0 0
1 2 3 4 5 6 7
1 Series
POT Cylinder with position transducer
2 Typology
F Anodized aluminium profiled barrel for SMT sensor bore 40 - 125
P Anodized aluminium profiled barrel bore 40 - 125
T Tie rods versions bore 40 - 125
3 Version
M Magnetic
S Non magnetic
4 Bore
Ø 40·50·63·80·100·125 mm
5 Standard stroke
50-100-150-200-250-300-350-400-450-500-600-700-800-900-1000 mm
6 Variants
SS Piston rod: no thread undercut
ES Piston rod seal: EPDM
CST Accessories: signal on voltage conditioner
CSC Accessories: signal on current conditioner
7 Special versions
AM..
Screw tap rod end with lenght on request
WH.. Rod protrusion on request
SD Rod end according to the customer's drawings
KK Metrical thread

 

Code example
ISO 15552 standard cylinder, magnetic, front cushioned, bore 50 mm, stroke 150 mm, with linear potentiometric transducer.
POTFM.050.0150

 

Magnetic switches


Extract from catalogue - magnetic switches (5.8Mb)

 

POTFM.4; POTFS.4; POTPM.4; POTPS.4; POTTM.4; POTTS.4; POTFM.5; POTFS.5; POTPM.5; POTPS.5; POTTM.5; POTTS.5; POTFM.6; POTFS.6; POTPM.6; POTPS.6; POTTM.6; POTTS.6; POTFM.8; POTFS.8; POTPM.8; POTPS.8; POTTM.8; POTTS.8; POTFM.1; POTFS.1; POTPM.1; POTPS.1; POTTM.1; POTTS.1; POTFM.1; POTFS.1; POTPM.1; POTPS.1; POTTM.1; POTTS.1;